Did you know?

5-YEAR LIMITED WARRANTY This Kobalt 40 V String Trimmer is warranted to the original purchaser from the original purchase date This Kobalt 40 V String Trimmer is warranted for the original user to be free from defects in material and workmanship. Page 19: Replacement Parts List 8 a.m. - 8 p.m., EST, Monday - Friday. This Kobalt (Lowe's) battery string trimmer has a straight shaft and weighs 10.8 lbs. It uses dual 0.080 or 0.095-inch cutting lines on a 14 or 16-inch diameter head. Shop11 Aug 2022 ... In today's video, I'm going to show you how to install weed warrior brush cutter blades on my kobalt 40v max trimmer.5.6K views 8 months ago. Kobalt weed eater string replacement tutorial. Check out the long tutorial where I show you step by step how to easily replace the Kobalt weed eater stringh...Step 3: Locating the small hole at the middle of the spool: First of all, find the eyelet or hole on the opposite side of the trimmer head. After finding the hole, wrap the strings around the hole. Keep pushing strings until the spool is full. Thrust half … The first step in stringing a Kobalt weed eater is to remove the old string. Here’s how to do it: Locate the spool housing on the bottom of the cutting head. It should be a round, plastic cover that is attached to the cutting head. Use your flathead screwdriver to pry off the spool housing cover. Wind the string onto the spool from side to side before overlapping to begin a second layer, so the string doesn't tangle when in use. Repeat with the second string on the opposite side of the spool, if applicable. Leave about 6 inches of string unwound at the end. Clip the end of the string in the notch located on the edge of the spool.You simply need to 'bump' your trimmer string out more often. Your string trimmer should dispense more trimmer string if the trimmer head is gently tapped on the ground. If you can depress the 'bump head' located at the bottom of your 'trimmer head,' this is how your weed eater is designed to work. Almost all somewhat new string trimmers will ...Hi readers, Hi readers, Legalizing cannabis is more than a cultural shift. The changing legal status of weed in the US, Canada, and other countries will transform it from an illega...ASSEMBLY INSTRUCTIONS 2. Connect upper/lower trimmer tubes a. Loosen the attachment knob (I) on the coupler. Release b. Push in the release button located on the lower button tube (K). Align the release button with the Positioning positioning hole on the upper tube (J) and slide the hole two tubes together.Connect upper/lower trimmer tubes a. Push in the release button located on the lower tube (K). Align the release button with the positioning hole on the upper tube (J) and slide the two tubes together. Rotate the lower tube until the release button locks into the positioning hole. 2 F Release button J Positioning hole b.Kobalt 40-Volt replacement spool, with easy wind head, fits the Kobalt 40-Volt multi-head string trimmer (KMS 1040A-03) Includes 15-ft of 0.080-in premium dual line. Genuine KOBALT parts ensure compatibility and qualityFold the cutting line in half and hook the folded end of the cutting line as shown in Fig. 9b. e. Wind the line, in two even and tight layers, onto the spool retainer. NOTICE: Failure to wind the line in the direction indicated will cause the cutting head to operate incorrectly.Kobalt replacement spool, with easy wind head, fits the Kobalt 40V string trimmer (KST 1040A-03/KST 1040B-03), and the Kobalt 24V string trimmer (KST 224A-03/KST 224B-03). Includes 15-ft of 0.080-in premium dual line. Genuine KOBALT parts ensure compatibility and quality. Overview.The Kobalt 40-Volt Max Brushless motor String Trimmer Kit tackles the toughest weeds. The string trimmer’s 15 inch cutting swath and dual side bump head make...Kobalt 40v Trimmer String Replacement. LifeHacksbyLW. 2.07K subscribers. Subscribed. 4.2K. 621K views 4 years ago #Kobalt #DIY #Weedwhacker. This video shows you how to restring you...

So here are the basic parts: - larger piece of wood (2x3) as the body; - small piece of wood as the winder. - large bolt through the body and winder. - a few washers to minimize binding. - 2 small nails in the winding handle, to engage the trimmer spool. Drill through the handle and the winder, so the long bolt will fit.We know how hard it can be to put new line in (or as some call it, re-string) a weedeater. We're making it simple for you! In this video, you'll see simple...DO AT YOUR OWN RISKHow I modified my 24V Kobalt item 3488480 Weed Eater to a Shakespeare UGLY HEAD trimmer head.It is equipped with the necessary 0.080 diameter line for your Kobalt 24-volt max string trimmer. The dual-line spool is pre-wound with 0.080 diameter line. For quick and easy line replacement for Kobalt 24-volt max string trimmer model #KST 1124B-03, KST 2024A-03 and item# 1504979 and 1137837. Package includes (1) dual-line spool with a total ...View and Download Kobalt KST 2540-06 manual online. 40 V LITHIUM-ION BRUSHED STRING TRIMMER. KST 2540-06 trimmer pdf manual download. Also for: 1438122.

How do I replace the string on my Kobalt weed eater? To replace the string on your Kobalt weed eater, first turn off the engine and unplug the spark plug. Then, remove the cap on the head of the weed eater and carefully remove any remaining string. Follow the instructions provided in your manual to add new string and secure the cap.1. Do not use the string trimmer. Trimmer head will not advance line. 1. The motor shaft or trimmer . head is bound with grass. 2. Not enough line in the spool. 3. Trimmer head is dirty. 4. Line is tangled on the spool. 1. Stop the trimmer, remove the. battery, and remove any grass. 2. Remove the battery and replace. the trimmer line. Reference ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. How do I replace the string on my Kobalt w. Possible cause: Mount the front-assist handle on the shaft as shown in Fig. Page 10 ASSEMBLY INSTRU.