Did you know?

Litter-Robot 3 is equipped with infrared emitters and sensors located above the waste drawer that check if the drawer is full each time the globe returns to the Home position. Once a full waste drawer is detected, the unit will indicate it is full with a blue flashing light.This video shows you how to get the 3 lights on the Litter-Robot 3 to stop blinking. Litter-Robot 3 Buying Options: 💵 Worried about your cats using it? Wan...Plug the Litter-Robot into the wall. Press the Power button to turn the unit on. Once the initial clean cycle is complete, the unit should return home displaying a blue 'ready light' …pjutras May 6, 2019, 1:53pm 6. Hi, The blue light will blink to indicate that the Drawer is full. If the blue light is blinking after each cycle even when you press the reset button, this mean that either there is something obstructing the way between the 2 DFI sensors or that the sensors themselves are defective.If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. Successful: If your unit returned home and displays a solid blue light, you've been successful.Preparation. Litter-Robot 4 continuously monitors the motor current to ensure the globe is rotating smoothly and is not obstructed. If your unit has a red light bar with partial yellow flashing, this indicates that the globe is most likely jammed or overloaded. The unit will retract and try to continue cycling. I'm at my wit's end since I'm going on a trip in a few months and I'll need the Litter Robot to be able to run while I'm away. Suggestions? Side note: I've been thinking about getting the LR4 but my understanding is shipping times are still crazy. edit: The new DFI unit fixed the issue. New pinch contacts were just $5 more so I got them too. The Litter-Robot 3 is quipped with Overload Detection.If the Globe becomes jammed or overloaded when rotating clockwise, the Motor will stop and reverse for ...Preparation. If Litter-Robot 4 displays a blue light bar with a blinking blue light adjacent to the Connect button, this indicates that the unit is connecting to the app or has disconnected and is trying to reconnect but has not successfully reconnected.My Litter Robot 3 has been having a weird issue for the last two weeks. When it cycles, the globe rotates counter-clockwise until the hall sensor detects the magnet on the globe. It …If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and ...If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. Successful: If your unit returned home and displays a solid blue light, you've been successful.If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful. If your unit is not displaying a solid blue light after ...Hi, I need help with my litter robot 3 please. The blue light is blinking although the waste drawer is empty. The other buttons do not react to pushing except the on/of one. I cleaned the sensors and all robot is clean. Please advise.Litter-Robot 4 user? Visit our support guiding on troubleshooting Litter-Robot 4 lights. Litter-Robot 3 illumination: Quick reference guide. If you’re looking for a quick view guide on show the Litter-Robot 3 lights, download one digital guide here alternatively click on the image below. Litter-Robot 3 flashing blue daylightSep 12, 2022 · Now, you’ll try these steps. Press the Cycle button and hold it for 5 seconds. You will see the blue and yellow lights on. Press the Cycle button and hold for 5 seconds again. Now, you’ll see the yellow light go off while the blue light stays on. Turn on the cat sensor (Press on the globe area above the entrace). The indication is a blue flashing light, and when it starts flashing, the Litter-Robot will continue to cycle automatically for approximately further cycles, allowing a little time to attend to the chan. There are 2 sensors that work together to monitor if the drawer is full and needing the liner removing and replacing. The indication is a blue ...1.) Leave your unit powered ON with the blue blinking light engaged and unplug your power supply from the base 2.) Wait 10 seconds, then plug the unit back in. 3.) Allow the unit to complete a start-up cycle. If the light is solid blue, the code has been successfully cleared. If the light is still blinking, let's proceed with troubleshooting.Why is my litter robot 3 blinking blue light not full? If you’re experiencing problems with your Litter-Robot 3, you may notice the blue light blinking. However, before attempting to fix the issue, it’s recommended that you unplug the power supply and wait for 10 seconds. After that, plug the unit back in and let it finish its cleaning cycle.Preparation. Litter-Robot 4 continuously monitors the motor current to ensure the globe is rotating smoothly and is not obstructed. If your unit has a red light bar with partial yellow flashing, this indicates that the globe is most likely jammed or overloaded. The unit will retract and try to continue cycling.The Litter-Robot is equipped with an Anti-Pinch safety feature to make the Litter-Robot extra safe for your cat. While cycling, if a potential pinch condition is detected, the globe will stop and reverse direction for 2 seconds. The yellow light will begin flashing quickly, about four times per second. You will also receive a notification on ...When a cat enters the globe, the cat sensor is activated; the blue light turns off and the red light turns on. Once the cat exits the globe, the countdown to a Clean cycle begins. ... If your Litter-Robot is flashing red or stuck upside down, complete the troubleshooting steps in our Litter-Robot 3: Red light flashing (Cat sensor fault) guide.

Here is the solution they provided, and now my litter robot is finally back to solid blue: "Here are the steps. Remove the bonnet → set aside the globe → place the bonnet back on. Press cycle. When the cycle ends, all three lights will flash on the control panel. Next, unplug the robot from the back of the base (not the wall) while it is ...LR3 slow blue / fast yellow flashing lights. Litter-Robot 3 Connect. LR3 non wifi model / 6 months old. Unit has a slow blue flash and when I hit reset it turns to a fast yellow flash. I changed the waste bin and noticed it wasn’t very full. Troubleshooting steps below. Waste drawer empty Waste liner not blocking DFI sensors Base 100% clean ...Constantly getting stuck upside down red and blue flashing lights so you pull the power cord out put it back in let it cycle stays upside down, then clean all of the sensors and it does it over and over again. If we hadn’t spent so much money on I’d just throw it over the fence. I read it was the curtain sensors.It's either space or blanketing the entire surface of the earth with solar panels. Amazon founder Jeff Bezos has shed new light on what’s driving him to invest billions in his spac...

Aug 18, 2021 ... Main problem is flashing blue light after every cycle, and my 7-8lb cat not activating the timer. (see update at end) Troubleshooting steps ...We recommend that you always keep your Litter-Robot’s firmware updated to ensure the best possible operation. If your unit temporarily displays a white light blinking in the middle of the light bar, this simply indicates that the unit was receiving an over-the-air firmware update. No action needs to be taken at this time.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. The Litter-Robot 3 is equipped with a cat sensor that detects whe. Possible cause: 1.) Press/Hold ‘Cycle’ button for 5 seconds. Both blue AND yellow lights are.